How do you connect a 12V trigger to a projector?
When active, a 12V signal is sent to the connected device while the projector is powered on.
- Connect a 3.5 mm stereo mini-jack cable to the external device’s trigger port.
- Connect the other end to one of the projector’s Trigger Out ports.
- Activate the trigger port in the projector’s Settings menu.
What is 12V trigger?
The 12 Volt Trigger is a powerful feature that comes equipped on all MSB powerbases and amplifiers. This simple 3.5mm mini-jack connection allows you to create a simple network between all of your MSB powerbases and amplifiers for a more seamless power up and standby experience.
What is 12V out on a projector?
A 12 volt trigger allows the projector, upon power up and power down, to automatically drop and raise a motorized screen.
What is trigger out on projector?
You can connect your projector to external devices such as motorized screens that support a trigger signal. When active, a 12V (200 mA maximum) signal is sent to the connected device while the projector is powered on. Turn on the Trigger Out setting in the projector’s Extended menu.
How do you power a projector screen?
Power the projector off and the screen retracts back into the casing. No further maintenance is necessary. Keep the wireless 12-volt trigger plugged into the projector. The projector’s power switch will activate the screen.
What is a trigger cable?
Power trigger cables for connection between e.g. amplifier and subwoofer, or pre- and power amplifier, so the units turn on and off together.
Can I use stereo cable for 12v trigger?
You absolutely can use a stereo cable. Everything is the same except for the division between the ring and the sleeve on the stereo one. You aren’t going to short anything or reverse polarity or literally cause any issues by using a stereo cable. Trigger works now.
How does a 12v trigger work?
If the switch is set to the ON position, the power amplifier will remain in standby mode until it detects a 12 volt signal at the 12V Trigger Input on the back panel. When the 12 volt signal disappears, the amplifier will return to standby mode.
How does a 12V trigger work?
What are trigger outputs?
A trigger is a device that facilitates simultaneously powering on and off multiple components within a larger stereo or home theater system. For example, use a trigger to automatically turn on a projector, receiver, amplifier, AV processor, TV speakers, and more when you activate a single device.
Can you put a projector on the floor?
Your projector is designed to be installed on a wall or ceiling (with the included mount). You can also place the projector on almost any flat surface (with the optional floor stand) to project an image in a portable setup, or on a lighting track (with the optional lighting track mount).
What does a 12 volt screen trigger do?
With three different basic types of screens out there (fixed wall, pull-down, and motorized), only those buying a motorized screen need to concern themselves with the 12 volt trigger issue. A 12 volt trigger allows the projector, upon power up and power down, to automatically drop and raise a motorized screen.
What kind of trigger does elite electric screen use?
Wireless Radio Frequency 5-12 volt trigger automatically controls your Elite electric screens (v2.0 – v3.0) up/down with your projector’s power cycle Eliminates the need to wire the connection from your projector to the screen for a clean installation
How does a 5-12 volt projector trigger work?
Wireless 5-12 volt projector trigger to automatically drop/rise your screen when your projector is turned on/off. Wireless Radio Frequency 5-12 volt trigger automatically controls your Elite electric screens (v2.0 – v3.0) up/down with your projector’s power cycle
What can I do with a 12V trigger?
You can either build a circuit that would switch on with the 12v trigger. Basically its a relay and a power supply. The other option which I use is to use a infra red plug socket its a plug socket that you program in the on off signals so you could teach if the commands for the on off signals from your amp.