How wide is a 74 Camaro rear end?
big gear head Veteran Member Measure the total width of the rear end. 60 inches is first gen and Nova, and 61 inches is second gen.
How do I know what size my rear end is?
The size of a rear differential, or rear end, is determined by the diameter of the ring gear inside the differential housing.
How wide is a 70 Camaro rear end?
big gear head The total width of the Chevy II rear end is 58 inches and the total width of a ’67 to ’69 Camaro rear end is 60 inches. The ’70 to ’81 Camaro rear end is 61 inches.
How wide is a 1970 Chevelle rear end?
Chevelle & Ford Rear End Widths
| Outside Width | Year | Model |
|---|---|---|
| 60.50 | 1964-1967 | Chevelle |
| 62.00 | 1955-1959 | Chevy Pickup |
| 61.25 | 1968-1972 | Chevelle |
| 62.50 | 1970-1981 | Camaro/Firebird |
How wide is a 71 Nova rear end?
MEASURED ACROSS WHEEL MOUNTING SURFACE
| Year | Classic Vehicles | Width Rear |
|---|---|---|
| 68-72 | Nova | 60″ |
| 78 & up | Monte Carlo, Regal, etc. with 10 bolt axle | 58″ |
| 68-72 | Chevelle with 10 bolt axle | |
| 89 | Trans AM (Disc brake) |
What is the best width for a Model A rear end?
most Model A guys try to get down to the 56 inch wide mark. There are no factory 9 inch Fords that narrow so folks use a 57 to 59 Ford car rear end ( 58 inches ) if they just have to have a 9 inch.
How do I find out my rear end gear ratio?
Count the number of teeth on the pinion gear and count the number of teeth on the ring gear. Divide the ring gear teeth number by the number of teeth on the pinion. The result is your gear ratio.
How can I tell what rear end my Silverado has?
Identify your GMC or Chevrolet rear end gear ratio by the RPO Codes, usually located on the placard labeled “Service Parts Identification” inside the drivers door panel or glove box.
Are all Ford 8.8 rear ends the same?
First appearing in 1977, the 8.8 is found in almost all Ford V8 cars from ’86 on, and in V6 Rangers and Explorers. There are 24 different Fords that offered the 8.8 rear axle. The 31-spline axles (1.29 inches in diameter) are more desirable but far less common.
How wide is a 66 Nova rear end?
MEASURED ACROSS WHEEL MOUNTING SURFACE
| Year | Classic Vehicles | Width Rear |
|---|---|---|
| 65-67 | Nova | |
| 68-72 | Nova | 60″ |
| 78 & up | Monte Carlo, Regal, etc. with 10 bolt axle | 58″ |
| 68-72 | Chevelle with 10 bolt axle |
How wide is a Chevy 10 bolt rear end?
The Chevy’S-10-bolt differential cover is oval in shape and measures 11 inches by 10.25 inches. It comes equipped with either A8. 5 inch oR8.
How can I tell what Chevy rear end I have?
All Chevrolet rear ends can be identified by comparing the gasket shape to an identification chart similar to the one found on Drivetrain’s differential identification page (see References). A visual chart of different GM/Chevrolet rear ends is found on Ring & Pinion’s differential types web page (see References).
What did the Pontiac Trans Am look like in 1974?
Trans Am’s sales finally soared, and after the 1974 season, the T/A would be all alone. The Pontiac Firebird Trans Am took on a new, more aerodynamic shape. The deformable endura bumper was gone, replaced with an unfriendly fibreglass front end and rubber covered 5-mph bumpers.
How do you drive a Pontiac Firebird Trans Am?
Slide the forward yoke over the transmission output shaft. Place the other end of the driveshaft into the rear axle yoke. Slide the shaft forward enough to clear the axle yoke ears and then pull it back slightly to seat the U-joint into the seat of the rear yoke.
What was the rear axle on a Pontiac Firebird?
The corporate 10-bolt rear axle was the mainstay of the second-generation Firebird. It was a robust axle assembly and the available axle ratios varied widely throughout its 11-year run.
How big is the bird on a Trans Am Firebird?
The small 12-inch bird mounted to the nose, which had been a Trans Am trademark (aside from the WW7 optioned cars), was no longer available. Instead all Firebirds received a bright flaming bird emblem mounted between the grilles.