How do I fix Harley p0152 code?
Using your multimeter, check for varying voltage of between . 1-. 95V on the signal wire of the bank 2 sensor 1 O2 sensor with the engine running at operating temperature. If this reading is consistently high, unplug the O2 sensor and see if the voltage changes.
How do you reset the limp mode on a Harley?
Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch to Ignition and release odometer reset button.
How do I identify my Harley engine?
Look on left side of the engine case for the engine number. Harley engines that were made before or in the 1960s have the model year of the engine as the first two numbers of the engine number, which acts as a VIN. Look for a four-digit production code in the last four digits of the VIN.
Is bank 2 sensor 1 upstream or downstream?
Bank 2 Sensor 1 means Upstream Left/Front; Bank 1 Sensor 2 means Downstream Right/Rear; Bank 2 Sensor 2 means Downstream Left/Front. Many buyers brought the wrong Oxygen Sensor because they donot pay attention to the plug and the length of the sensor.
How do I reset my electronic throttle on my Harley?
Reset the TPS. Turn ignition switch on for 10 seconds, then off for 10 seconds (Don’t start engine). Repeat a total of 4 times. DO NOT TOUCH throttle while doing it.
What is limp mode on a Harley?
Limp Mode happens when there is a correlation error between the twist grip sensor, electronic control module, and throttle control actuator. It limits the RPMS and throttle response of the bike. Basically, it lets you limp the bike home or to a shop to get it repaired.
How do you decode a Harley Vin?
The VIN numbers affected are 43000H9 through 48199H9. The engine numbers where 10 digit numerical IDs….Model Codes:
| 1A = FL/FLP-1200 | 3D = Z-90 | 2G = XLT-1000 |
|---|---|---|
| 3A = XL – XLH-1000 | 5D = SX-175 | 5G = FLT-80 |
| 4A = XLCH-1000 | 6D = SX-250 | 6G = FXE-80 |
| 5A = GE-750 | 7D = MX-250 | 7G = FXS-80 |
What Harley models are being recalled?
Bikes. The NHTSA issued a recall that includes all Model Years from 2008 to 2011 of the Touring, CVO Touring, and VRSC motorcycles outfitted with ABS.
What does the code p0152 on the ECM mean?
Code P0152 is triggered when the Engine Control Module (ECM) detects an abnormally high voltage (approximately 1.2V or higher) on the signal circuit of the bank 2 sensor 1 Oxygen (O2) Sensor for an extended period of time. Bank 1 is the bank with cylinder 1, bank 2 is the opposite bank.
Where are the p1511 and p2135 codes?
Check engine light came on twice and went into ‘Limp Home Mode’. When I got home I retrieved two codes. P1511 and P2135. Any help as to where I start looking?
What is the throttle grip code on a Harley Davidson?
I have a 09 Ultra with 10,000 miles on it. I baby the bike most of the time except for last week I was riding it more agressive and the check engine light came on and it went into lymp home mode. I checked for codes and it came up with P1511. The manual says it is the Throttle Grip Sensor. I replaced it and cleared the code.
How to find the Diagnostic Code on a Harley Davidson?
Harley Diagnostic Codes To access codes 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold. 3- Turn ignition switch to Ignition and release odometer reset button. Background lighting sould illuminate,