How do I restore reflash QNAP firmware documents?

When to use the firmware recovery guide

  1. Power off the NAS.
  2. Remove all the hard disks.
  3. Power on the NAS.
  4. Wait for ten seconds and check if you hear a short beep.
  5. After the short beep, wait for two minutes to check if you hear a long beep.

How do I reset my QNAP without losing data?

Use one of the following methods:

  1. Basic system reset using QES. Go to Control Panel > System > Hardware > Backup/Restore > Restore to Factory Default. Click Reset Settings.
  2. Basic system reset using the reset button. Power on the NAS. Press and hold the reset button for 3 seconds.

Where can I download QNAP BIOS?

Go to, and download the compressed NAS BIOS file. Extract the compressed file contents. Copy the extracted files to the root or a folder on the USB flash drive.

What is the default password for QNAP?

The default password of admin is admin, You can login the NAS via admin/admin after resetting the NAS. The default password for admin is changed to the first MAC address of NAS in uppercase letters and without special characters. You can login the NAS via admin/00089BF615755 after resetting the NAS .

What is the default IP address for QNAP NAS?
Note: The default NAS IP is 169.254. 100.100:8080. If the NAS has been configured to use DHCP, you can use QNAP Qfinder to check the IP address of the NAS.

How long is QNAP warranty?

2 to 5 year
QNAP offers industry leading free 2 to 5 year limited warranty service on our products. If the standard warranty period is not long enough, QNAP offers optional purchase extended warranty service (QEWS) coverage that will provide warranty for 1, 2, or 3* additional years.

How long does it take to reset QNAP?

Boot up/restart/shutdown takes a really long time (15-20 minutes). Why is this? A QNAP NAS generally takes around 2-3 minutes to boot up. This number can be further influenced by a few other factors such as the number and capacity of drives currently installed.

Where is the reset button on QNAP?

Hardware reset by the physical reset button located on the back of the unit. Please find a sharp object such as a paperclip or pin and insert it to the hole located below the “Reset” sign on the back of the unit. A little click can be felt when the button is pressed.

How do I connect QNAP to my network?

How to set up and connect to your QNAP NAS

  1. Turn on the NAS.
  2. Look up the IP using your router or download QNAP Qfinder Pro to search.
  3. Load the IP address in your favorite browser.
  4. Follow the initial setup wizard to configure the NAS. Source: QNAP.
  5. Once complete, you’ll be greeted by QTS and are ready to go.

How does recovery mode of QNAP ts-21x work?

The recovery mode will first request an IP address via DHCP and then request a recovery image by TFTP from a server on your network. You have to configure your DHCP server so it will request the right file from the right machine. In particular, you have to create an entry for your QNAP that specifies filename and next-server.

How does QNAP recovery mode work in Debian?

In case your Debian system no longer boots after a system upgrade, you can use the QNAP system recovery mode to restore a previous image, an image of the Debian installer, or the QNAP firmware. The recovery mode will first request an IP address via DHCP and then request a recovery image by TFTP from a server on your network.

How to install the firmware for a QNAP NAS?

Enter your “Cloud Key” and follow the instructions to install the firmware. Please download QNAP utility “Qfinder Pro” based on your operating system to start firmware installation. After downloading Qfinder Pro, please install it on your PC. This utility will help you to locate and configure the QNAP NAS on the LAN.

How to reflash firmware for ts-119p II / 219p II?

TS-119P II/219P II/419P II 2 – Download and install Virtual Box; 3 – Setup Vrtualbox: Step 1 :Start software and Choose “New”; Step 3 : choose “Create a Virtual Drive Now” Step 4 : Choose VDI -> Dynamical allocated 4 – right click to your virtual server -> Settings ->storage.